Enclosures feature multi-layer reinforced fiberglass and steel end-panels. Grilles are zinc plated, powder coated 14-gauge perforated steel with an acoustically transparent black grill cloth backing, a hydrophobic mesh underlayer, and a waterproof rail system.
The rigging system is inherent to the design of the system. Inter-box angles are selected when the array is assembled. Other accessories include a rigging frame, pull-back bar, and a cardioid kit.
Features
Compact line array module optimized for permanent install applications
Advanced technology component transducers for low weight and high output
Outdoor IP55 rated enclosure for protection from dust and water
Comprehensive rigging points for creating a line array configuration
Fiberglass box construction and weatherized components
Dual 15” transducers.
Specifications
Frequency Range (-10dB)
52 Hz – 210 Hz
Frequency Response (±3 dB)
62 Hz – 123 kHz
System Power Rating
1600 W Continuous Pink Noise (6400 W peak), 2 hrs800 W Continuous Pink Noise (3200W peak), 100 hrs
Maximum Input Voltage
80 V Rms (2 hrs), 160 V peak
Maximum SPL (1m)
127 dB Cont. Ave (2 hrs), 133 dB Peak
Sensitivity
98 dB (52 Hz – 210 Hz, 2.83V)
Impedance
4Ω, 3.0Ω min @ 195 Hz
Amplifiers
Crown DCi Family with DSP on-board
Recommended
Crown DCi 2 | 2400N Crown DCi 4 | 2400N
LF Driver
2 x 2275H, 304 mm (15 in) diameter , each with two 76 mm (3 in) diameter voice coils, Neodymium Differential Drive®, Direct Cooled™
Enclosure Material
Fiberglass shell, gelcoat finish, with 18 mm Birch plywood internal bracing.
Grille
Powder coated 14 gauge hex-perforated steel with zinc under-coating, backed with acoustically transparent cloth and hydrophobic screen.
Inter-Enclosure Angles
VLA-C125S to VLA-C125S: 0° using VLA-C125S Bracket Plate (included with VLA-C125S)VLA-C265 below VLA-C125S Subwoofer (VLA-C265 cannot be connected above C125S): 0°, 5° using VLA-C125S Bracket Plate (included with VLA-C125S)VLA-C2100 below VLA-C125S Subwoofer (VLA-C2100 cannot be connected above C125S): 0°, 7.5° using VLA-C125S Bracket Plate (included with VLA-C125S)
Environmental
IP-55 rating per IEC529 (dust protected and protected against jets of water).
Terminals
CE-compliant covered barrier strip terminals. Barrier terminals accept up to 5.2 sq mm (10 AWG) wire or max width 9mm (0.375 in) spade lugs. Touch-proof covers. Full set of terminals on back panel, plus optional-use inter-cabinet connection terminals located on top and bottom panels of cabinet.
Colors
-GR: Gray (similar to Pantone 428C), -BK: Black
Dimensions (H x W x D)
508 x 848 x 634 mm (20.0 x 33.4 x 24.9 in)
Net Weight (each)
56.7 kg (125 lbs)
Shipping Weight (ea)
62.6 kg (138 lbs)
Included Accessories
2 x VLA-C125S Bracket Plates
8 pcs. M10 x 35 mm stainless steel bolts (1.5mm pitch, 6 mm hex-drive) for attaching Bracket Plates
2 pcs. Plastic Trim Cover Panels for Bracket Plates, each attaches via
4 pcs (8 total) 3-32 x ½” trusshead, phillips-drive, stainless steel bolts.
Optional Accessories
VLA-C-SB2 (JBL-VLACSB2BK) Suspension Bracket Kit
VLA-C125S-ACC Kit – For wiring of 3 VLA-C-125S subwoofers in cardioid configuration (2 front-facing and 1 rear-facing). Allows for neat, unexposed inter-cabinet wiring via the tops and bottoms of cabinets.
JBL
EON SERIES LOUDSPEAKERS
JBL
